Mechanical properties,corrosion resistance,and rubber pad forming of cold differential speed-rolled pure titanium for bipolar plates of proton-exchange membrane fuel cells

Due to problems such as pores on surface-treated coatings, the corrosion resistance of pure titanium bipolar plates for proton-exchange membrane fuel cells can be further improved by increasing the corrosion resistance of pure titanium by using differential speed-rolling (DSR); however, these materials have not yet reached the standard requirements of bipolar plates (corrosion current density i_corr＜10³ nA·cm^?2). In this work, the corrosion resistance of pure titanium was improved by optimizing the DSR process while the strength was maintained. The best corrosion resistance of the DSR pure titanium was achieved when the roller speed ratio was 2, while i_corr was 429 nA·cm^?2 in a solution of 0.5 M H₂SO₄ and 2 mg/L HF at room temperature. The formability of the DSR pure titanium for bipolar plates was verified. The optimal holding pressure range was 6.8–7.0 kN.     

Investigation of stress fields for non-standard sized glass plates loaded by ring-on-ring

A ring-on-ring (ROR) test is a prevailing test method for evaluating the equi-biaxial strength of glass materials. However, current ROR test standards limit the strength and size of glass to prevent a nonlinear behavior. In this study, the feasibility of ROR testing for non-standard, high-strength glass, such as tempered or ion-exchanged rectangular glass is investigated. To this end, ROR simulation based on theory and experiment is conducted for thirty non-standard glasses with widths of 100–300 mm and aspect ratios of 1.0–2.0. As a result, the maximum measurable stress was about 215.6 MPa for 100 × 200 mm glass and 481.3 MPa for 300 × 600 mm glass with a 3% deviation, which is well above the strength of regular tempered glass. The main purpose of this work is to understand the range of aspect ratio of horizontal and vertical widths of a glass plate that can be evaluated by the standard ROR test.     

基于压缩机-支架系统的异常噪声研究

针对某乘用车发动机转速在1 573 r/min，压缩机开启时车内噪声异常的问题，对样车进行试验分析与诊断，对压缩机-支架系统进行仿真分析，提出改进方案并验证改进效果。利用LMS声振信号采集系统采集振动噪声数据，采用频谱分析、阶次追踪等方法，并结合压缩机-支架系统模态仿真结果，确定车内异常噪声是压缩机轴频21阶与压缩机-支架系统3阶模态频率接近发生共振造成的。通过优化支架结构来提高压缩机-支架系统3阶模态频率以此来避免共振，并换装橡胶驱动盘缓和压缩机输入扭矩波动。将改进结构进行整车试验，结果表明：匀速工况空调开启时问题转速下，车内噪声降低了2.5 dB(A)；匀加速工况空调开启时发动机转速1 500~1 650 r/min区间，车内噪声无峰值，其余转速空调开启时改进前/后车内噪声基本不变，噪声波动趋势平缓。     

A hybrid knowledge and ensemble classification approach for prediction of venous thromboembolism

Clinical narratives such as progress summaries, lab reports, surgical reports, and other narrative texts contain key biomarkers about a patient's health. Evidence-based preventive medicine needs accurate semantic and sentiment analysis to extract and classify medical features as the input to appropriate machine learning classifiers. However, the traditional approach of using single classifiers is limited by the need for dimensionality reduction techniques, statistical feature correlation, a faster learning rate, and the lack of consideration of the semantic relations among features. Hence, extracting semantic and sentiment-based features from clinical text and combining multiple classifiers to create an ensemble intelligent system overcomes many limitations and provides a more robust prediction outcome. The selection of an appropriate approach and its interparameter dependency becomes key for the success of the ensemble method. This paper proposes a hybrid knowledge and ensemble learning framework for prediction of venous thromboembolism (VTE) diagnosis consisting of the following components: a VTE ontology, semantic extraction and sentiment assessment of risk factor framework, and an ensemble classifier. Therefore, a component-based analysis approach was adopted for evaluation using a data set of 250 clinical narratives where knowledge and ensemble achieved the following results with and without semantic extraction and sentiment assessment of risk factor, respectively: a precision of 81.8% and 62.9%, a recall of 81.8% and 57.6%, an F measure of 81.8% and 53.8%, and a receiving operating characteristic of 80.1% and 58.5% in identifying cases of VTE.     

刮板输送机中板仿生耐磨优化试验研究

刮板输送机中板磨损失效已成为输送机运行故障的主要原因之一，为了提高中板耐磨性，基于蜣螂非光滑单元进行了仿生中板设计，以磨损量为响应值，进行了单因素和响应面法优化试验。根据响应面法试验结果得到的因素显著性影响顺序（从高至低）依次为：径向距离，深径比，直径，节距角。基于试验结果建立了磨损量与因素的回归预测模型，经试验对比发现，预测模型与真实试验的相对误差为3.2%。在特定工况（煤散料粒度为6~8 mm、载荷为20 N、刮板链速为0.65 m/s及试验时长为6 600 s）下，当深径比为1.41、直径为0.69 mm、节距角为6.55°和径向距离为4.66 mm时，磨损量最小，仿生中板的耐磨性提高了12.6%。分析其耐磨机理发现，与光滑板相比，仿生板的磨粒磨损及黏着磨损较轻。凹坑分布可破坏持续切削中板表面的煤粒运动状态。中板的仿生优化可为今后刮板输送机的设计提供一定参考。     

优化作业方式提高始极片质量

针对某厂铜电解种板工序存在的始极片质量波动较大的问题,从种板系统体积控制和添加剂匹配的角度出发,分析各种因素对始极片质量的影响,做出了相应的改进措施,使种板系统运行更加稳定,始极片质量得到进一步提升。     

The analysis and comparison of two novel kinds of focusing elements as reflectors

In this article, two novel kinds of focusing elements as reflectors are analyzed and compared. One is the grooved Fresnel zone plate reflector with continuous phase‐correcting. The other called subzone paraboloid reflector, has the profile that consists of a series of paraboloids. Their diffraction efficiencies and bandwidths are described. The two elements still preserve the advantages of Fresnel zone plates, namely, low profile, high efficiency, and simple fabrication. Two dual‐reflector antennas using the proposed focusing elements as the main reflectors are simulated and the results show that these antennas have good radiation performances. © 2014 Wiley Periodicals, Inc. Int J RF and Microwave CAE 25:101–108, 2015.     

Thermal imaging of time-varying longitudinal defects in the internal coating of a tube

We deal with the mathematical model of the incremental degradation of the internal coating (e.g. a polymeric material) of a metallic pipe in which a fluid flows relatively fast. The fluid drags solid impurities so that longitudinal scratches, inaccessible to any direct inspection procedure, are produced on the coating. Time evolution of this kind of defects can be reconstructed from the knowledge of a sequence of temperature maps of the external surface. The time-varying orthogonal section of this damaged interface is determined as a function of time and polar angle through the identification of a suitable effective heat transfer coefficient by means of Thin Plate Approximation.     

350MW机组锅炉SCR脱硝系统优化

准东煤田是我国目前最大的整装煤田,但准东煤在锅炉燃烧过程中易发生结焦问题,一般掺烧高岭土缓解结焦。某燃用准东煤350 MW机组,锅炉燃煤掺烧高岭土后烟气携带灰尘颗粒及灰尘量增大,出现SCR脱硝系统烟道积灰严重和喷氨量明显偏大问题,同时在空气预热器形成硫酸氢氨堵塞,使机组不能长周期稳定运行。通过与国内同类型多台机组锅炉对比后发现,脱硝系统均存在易产生积灰的脱硝转向室、催化剂上方及空气预热器入口斜坡积灰状况等情况。针对存在的问题,通过建立改造前、后的模型计算分析,进行了导流板布置的优化设计、CFD流场分布、优化SCR系统导流板设计、声波与蒸汽吹灰器结合吹灰和氨注射栅格优化升级等工作,应用德图480风速仪实测风速试验,发现脱硝烟道原导流板设计不合理及施工安装偏差;原导流板水平段跨距大,支撑不足,造成导流板压塌变形,影响烟气流场分布;锅炉所烧煤质为高钠煤,为防止锅炉结焦掺烧高岭土后,增加了烟气飞灰颗粒及灰尘量,飞灰具有很大黏性,易沉积在烟道导流板及烟道壁面上。因此,提出对脱硝内部各处导流板进行优化改造,对脱硝系统烟道易产生积灰的部位增加声波吹灰器,对喷氨格栅喷嘴数量及氨空混合器升级,同时开展锅炉SCR脱硝喷氨热态优化调整试验工作。通过开展相关工作,SCR烟气系统的烟气流场相对标准偏差优化5%,相同负荷下液氨消耗量降低45%,彻底解决脱硝系统积灰和空气预热器堵塞问题,实现机组满负荷达标稳定运行。锅炉长期运行半年后停炉检查,发现前期脱硝系统烟道高达1 m的积灰部位彻底解决,催化剂表面干净无杂物,解决了脱硝系统积灰问题,同时配合提高空气预热器冷端综合温度的措施,彻底解决锅炉空气预热器堵塞问题。同时,经济效益显著,每年可以分别节约液氨费用70万元,节约风机电耗费用100万元,节约检修清理积灰及检修费用80万元,节约空气预热器冲洗治理费用20万元,综合节约费用270万元/a,达到预期效果实现机组长周期安全经济稳定运行。